|
06-12-2007, 09:27 PM | #1 | ||
not here much anymore
Join Date: Dec 2004
Location: Sthn NSW
Posts: 22,918
|
Im after a bit of info on how to run new wiring from the inside of the car to the doors, anybody done this and if so can you help me out a bit?
I need to run 2 new wires to each door to power the doortrim lights Ive just put in, I can see where they go through the grommet to get to the door, but how do I get to that area of the car to put the wires in ie what bits of the dash are going to have to come out. Any ideas on how to make this a painless experience?
__________________
2024 F150 XLT
|
||
06-12-2007, 09:40 PM | #2 | ||
Wanting a sprint!
Join Date: Jul 2007
Location: In Between The Lines!
Posts: 925
|
i'd say remove kicker panels and undo the plastic to move the carpet back for the back doors, coz i would think itll run through the seal panels and will have gromments on the inside.
If thats the sortta information your after , Good Luck regards Craig
__________________
On track for mint turbo falcon |
||
06-12-2007, 10:04 PM | #3 | |||
FTF Club Moderator
Join Date: Jan 2005
Location: Driving my Tickford T3 Wagon in Sydney
Posts: 3,132
|
Quote:
I have had to do this. Or should I say Stav did this for me. Run a power wire from the light that shines on the ignition barrel. You only want the door lights on when that light is on anyway. You can just earth the other wire some where convenient for you.You will need about 2 meters of wire. To go down the steering column, behind the dash, kick panel out the grommet and through to the door.
__________________
Albert Einstein: Es ist schwieriger, eine vorgefaßte Meinung zu zertrümmern als ein Atom. (It is more difficult to alter a preconception than split an atom) Falcon Tickford FPV (FTF) Car Club of NSW Fords in the Park 2010 I use and recommend Stingray Car Security. http://www.stingraycar.com.au/ |
|||
06-12-2007, 10:18 PM | #4 | |||
not here much anymore
Join Date: Dec 2004
Location: Sthn NSW
Posts: 22,918
|
Quote:
So the grommet I need to get to is behind the kick panel by the soubds of it.
__________________
2024 F150 XLT
|
|||
06-12-2007, 11:00 PM | #5 | ||
FTF Club Moderator
Join Date: Jan 2005
Location: Driving my Tickford T3 Wagon in Sydney
Posts: 3,132
|
IIRC yes. I can have a look in the morning to check. There is a flexible rubber hose that has the wires in it for the power mirrors and power windows. Just use that grommet to get from in the cabin to behind the door trim.
__________________
Albert Einstein: Es ist schwieriger, eine vorgefaßte Meinung zu zertrümmern als ein Atom. (It is more difficult to alter a preconception than split an atom) Falcon Tickford FPV (FTF) Car Club of NSW Fords in the Park 2010 I use and recommend Stingray Car Security. http://www.stingraycar.com.au/ |
||
06-12-2007, 11:00 PM | #6 | |||
You can't stop the signal
Join Date: Nov 2005
Location: Behind a computer at work
Posts: 1,624
|
The area you need to get to is up under the dash a bit. No parts of the dash have to come off but you will need to pull back the carpet to get to the other side of the grommet.
As for getting wires through, use a piece of wire (my choice was coat hanger) smother it in Vaseline then poke it through the grommet. This will take some playing around. Once through, tape the wires to the coat hanger, cover them in Vaseline as well and pull it all back through. Sounds easy huh? trust me it's not. Plenty of swearing will be done. At least it will probably be easier than mine Cheers
__________________
Quote:
|
|||
07-12-2007, 08:31 PM | #7 | ||
not here much anymore
Join Date: Dec 2004
Location: Sthn NSW
Posts: 22,918
|
Found them tonight, well the driver's side one anyway, I think the passenger side is going to be the worst with the ECU wiring everywhere. Its going to be a right bugger of a job methinks.......doh..........
__________________
2024 F150 XLT
|
||
07-12-2007, 08:34 PM | #8 | |||
FF.Com.Au Hardcore
Join Date: Apr 2005
Location: Moree, NSW
Posts: 2,076
|
Its a sh%t of a job to get wiring through to passagers side. When i ran my new speaker wire i went from the door into the car and managed to fish them down and out past the ECU
__________________
Nathan 2005 FPV BF Super Pursuit The new toy (now sold) The SP The old ute (sold) www.aufalcon.com/nc1183 Build Thread Quote:
|
|||
07-12-2007, 08:41 PM | #9 | ||
Sales Representative
Join Date: Mar 2007
Location: Young
Posts: 5,314
|
Ah crap... looks like i'm going to be for some fun too... as i want heavier speaker wire and wouldnt mind the door lights in future (when i get matching trims)... so i might run ome extra wires while im at for the future. :P
__________________
Project InfernoSR - Back Burner Project FeralTerra - No longer Project Fairmont Prodigy - Sold Thanks go to: MY WIFE! Bathurst Brakepro Undacar eBay!! |
||
07-12-2007, 08:52 PM | #10 | ||
Wanting a sprint!
Join Date: Jul 2007
Location: In Between The Lines!
Posts: 925
|
Yeah sweet it would save alotta fustration down the track what a pain in the a@# lol.
__________________
On track for mint turbo falcon |
||
07-12-2007, 09:43 PM | #11 | ||
Miami Pilot
Join Date: Jan 2005
Location: ACT
Posts: 21,704
|
You guys could try external door lights on your mirrors instead of inside. Why would I suggest that ? Because that's what our Explorer has. Don't ask, 'cos I don't know!
__________________
-----------------------------------------------------------------
The Hammer: FG GTE | 376rwkw | 1/4 mile 11.793 @ 119.75mph 1.733 60' (4408lb) 1 of 60 FG MK1 335 GTEs (1 of 118 FG Mk 1 & 2 335 GTEs). Mods: Tune, HSD/ShockWorks, black GT335 19” staggered replicas with 245 & 275/35/19 Michelin Pilot sport 5s Daily: BF2 Fairmont Ghia I6 ZF, machine face GT335 19” staggered Replicas with 245s and 275s, Bilsteins & Kings FPV 335 build stats: <click here> Ford Performance Club ACT |
||
07-12-2007, 10:21 PM | #12 | ||||
You can't stop the signal
Join Date: Nov 2005
Location: Behind a computer at work
Posts: 1,624
|
Quote:
Cheers
__________________
Quote:
|
||||