|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
20-03-2009, 02:35 AM
|
#1 | ||
|
Starter Motor
Join Date: Mar 2008
Posts: 22
|
Hi all
I hope you guys (& girls) can help. My 1993 Ford TX5 is a manual, with about 180000km's on the clock. When I start my car, it starts fine but idles quite rough. Not that the car is shaking, but I can feel and see on the gear leaver how it vibrated. I can't remember it ever doing that, until I got a refurbished distributor. I've taken it to some Ford mechanics and some has said that the "HT/HD leads" might have to be replaced. Question is, is that the problem? I know I'll never know until I actually replace them, but what else could be causing the gear lever to vibrate so much? It never was so bad since I got that other refurbished distributor. Any advice will be much appreciated. Thanks Everyone!! |
||
|
|
|
23-03-2009, 04:46 PM
|
#2 | ||
|
Over Thinker
Join Date: Dec 2005
Location: Ipswich Qld
Posts: 1,351
|
at night in the dark lift the bonnet and run the motor
look for arcing of the leads /cap /coil
__________________
My car goes Brumm Brumm |
||
|
|
|
|
24-03-2009, 09:30 PM
|
#3 | ||
|
Starter Motor
Join Date: Mar 2008
Posts: 22
|
Hi Dirty Hands
With "arcing of the leads /cap /coil", do you mean like sparks or something? I'm not quite up to date with the terms. |
||
|
|
|
|
25-03-2009, 01:28 AM
|
#4 | ||
|
Over Thinker
Join Date: Dec 2005
Location: Ipswich Qld
Posts: 1,351
|
yes sparkles of light by the current through the insulation
__________________
My car goes Brumm Brumm |
||
|
|
|
|
18-04-2009, 03:22 PM
|
#5 | ||
|
Stealth Operator
Join Date: Apr 2009
Location: North of the Border
Posts: 320
|
Is taking it back to whoever did the distributor an option? Tell them it has been idling rough since they did the work and ask them nicely to have a quick look to make sure they didn't miss something during the job.
HT leads have a resistance of about 15K-ohms per metre. Check this with a multimeter. Bad leads usually go high resistance, so anything more than 20-30K-ohms per metre should be replaced. Bad HT leads give poor fuel economy, rough idle and/or off-idle hesitation and can cause failures in other parts of the ignition system. |
||
|
|
|
|
07-08-2010, 01:36 AM
|
#6 | ||
|
Starter Motor
Join Date: Mar 2008
Posts: 22
|
Hi Stocko
I'm afraid there's no option for me to take it back. First mistake I made, was putting in a refurbished distributor.. 
|
||
|
|
|
|
09-08-2010, 05:01 PM
|
#7 | |||
|
FF.Com.Au Hardcore
Join Date: Sep 2005
Posts: 1,360
|
Quote:
I'd be checking that the timing was set correctly when doing the distributor install & that your plug leads aren't breaking down (they get very brittle internally with age). New plug leads shouldn't be too many $$$ |
|||
|
|
|
Ford TX5 - idles rough
Linear Mode
