Welcome to the Australian Ford Forums forum.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact us.

Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated.

Go Back   Australian Ford Forums > General Topics > The Pub

The Pub For General Automotive Related Talk

Reply
 
Thread Tools Display Modes
Old 07-07-2017, 09:27 PM   #1
IH8HSV
XR6T 400kw(well one day!)
 
IH8HSV's Avatar
 
Join Date: Dec 2005
Location: Toodyay W.A.
Posts: 1,008
Default Fault codes causing limp mode

Hi all,

My mums car is going into limp mode.

We took it to super cheap and got the following codes:

P1270 ( engine speed rev / limiter reached )
P2110 ( throttle actuator control fault ( TAC ))
P1507 ( idle air control fault ( IAC ))

Can someone please shed some light on what could be wrong?

Im trying to find a link between the throttle actuator and the idle air control.

Thanks in advance.
__________________
If it Vibrates, rattles, squeaks or knocks - then it must be a Territory
IH8HSV is offline   Reply With Quote Multi-Quote with this Post
Old 07-07-2017, 09:33 PM   #2
IH8HSV
XR6T 400kw(well one day!)
 
IH8HSV's Avatar
 
Join Date: Dec 2005
Location: Toodyay W.A.
Posts: 1,008
Default Re: Fault codes causing limp mode

Here is the actual super cheap sheet.

Obviously the first 3 highlighted lines are my concern.

Thanks.

https://ibb.co/btgScv
__________________
If it Vibrates, rattles, squeaks or knocks - then it must be a Territory
IH8HSV is offline   Reply With Quote Multi-Quote with this Post
Old 07-07-2017, 11:15 PM   #3
lucas2
FF.Com.Au Hardcore
 
lucas2's Avatar
 
Join Date: Jul 2011
Posts: 1,017
Default Re: Fault codes causing limp mode

What's the battery like? That can cause issues and may be worth looking into before you go replacing lots of parts.
__________________
BF MKII XR6 CONQUER (SOLD)

FG XR6T SILHOUETTE - 380rwkw
lucas2 is offline   Reply With Quote Multi-Quote with this Post
Old 07-07-2017, 11:29 PM   #4
bawagon2012
Starter Motor
 
Join Date: Jun 2012
Posts: 14
Default Re: Fault codes causing limp mode

Sounds like a Throttle position sensor (TPS) Fault, Or as lucas2 said the Battery.
bawagon2012 is offline   Reply With Quote Multi-Quote with this Post
Old 07-07-2017, 11:49 PM   #5
GO FURTHER
Moderator
Donating Member3
 
GO FURTHER's Avatar
 
Join Date: Jan 2014
Location: Melbourne
Posts: 7,965
Tech Writer: Recognition for the technical writers of AFF - Issue reason: Fitting New Iridium Plugs & the state of the old ones - (Photo Essay) 
Default Re: Fault codes causing limp mode

Quote:
Originally Posted by IH8HSV View Post
My mums car is going into limp mode.
P1270 ( engine speed rev / limiter reached )
Hmm... Are you sure it's your mum's car?
GO FURTHER is offline   Reply With Quote Multi-Quote with this Post
This user likes this post:
Old 08-07-2017, 01:47 AM   #6
aussiblue
FG XR6 Ute & Sedan
Donating Member3
 
Join Date: Oct 2006
Location: Bibra Lake WA
Posts: 22,302
Technical Contributor: For members who share their technical expertise. - Issue reason: Has been floating around the oze tech section for a long time and is always there to give advice when people have an issue. 
Default Re: Fault codes causing limp mode

Those 3 codes with U prefix suggest either the scanner was not fully plugged into the diagnostic port (the most common cause), the scanner is faulty or the diagnostic port is faulty. As a first step you need to get it scanned again perhaps elsewhere and make sure the scanner plug is pushed into the diagnostic port as far as it will go.
__________________
regards Blue
aussiblue is offline   Reply With Quote Multi-Quote with this Post
Old 08-07-2017, 12:28 PM   #7
IH8HSV
XR6T 400kw(well one day!)
 
IH8HSV's Avatar
 
Join Date: Dec 2005
Location: Toodyay W.A.
Posts: 1,008
Default Re: Fault codes causing limp mode

It seems to shudder and feels like its going to stall but doesnt - mainly at low speed.

Then sometimes it will just lose power and stop. Once I restart it then its ok.

Anymore suggestions please?
__________________
If it Vibrates, rattles, squeaks or knocks - then it must be a Territory
IH8HSV is offline   Reply With Quote Multi-Quote with this Post
Old 08-07-2017, 04:03 PM   #8
ratter
FF.Com.Au Hardcore
 
ratter's Avatar
 
Join Date: Feb 2005
Location: Pit Lane
Posts: 11,871
Valued Contributor: For members whose non technical contributions are worthy of recognition. - Issue reason: Shares his in-depth tuning knowledge with the forum, very helpful. Contributor: For members who make a contribution worthy of recognition. - Issue reason: For his indepth tutorial on adding borders to photographs 
Default Re: Fault codes causing limp mode

I would be checking for vacuum leaks
__________________
Pit Lane Performance
20 Rosella St Frankston 03 9783 8122

Authorised Streetfighter, Pcmtec , SCT & HP Tuners Tuning Agent,
ratter is offline   Reply With Quote Multi-Quote with this Post
This user likes this post:
Old 08-07-2017, 04:37 PM   #9
aussiblue
FG XR6 Ute & Sedan
Donating Member3
 
Join Date: Oct 2006
Location: Bibra Lake WA
Posts: 22,302
Technical Contributor: For members who share their technical expertise. - Issue reason: Has been floating around the oze tech section for a long time and is always there to give advice when people have an issue. 
Default Re: Fault codes causing limp mode

It might also be that the ECU plugs have come loose; see http://www.fordmods.com/post1394839.html
__________________
regards Blue
aussiblue is offline   Reply With Quote Multi-Quote with this Post
Old 08-07-2017, 06:49 PM   #10
IH8HSV
XR6T 400kw(well one day!)
 
IH8HSV's Avatar
 
Join Date: Dec 2005
Location: Toodyay W.A.
Posts: 1,008
Default Re: Fault codes causing limp mode

OK Thanks.

Where are these plugs located?

Also whats the best way to test for vacuum leaks?

Thanks.
__________________
If it Vibrates, rattles, squeaks or knocks - then it must be a Territory
IH8HSV is offline   Reply With Quote Multi-Quote with this Post
Old 08-07-2017, 06:54 PM   #11
aussiblue
FG XR6 Ute & Sedan
Donating Member3
 
Join Date: Oct 2006
Location: Bibra Lake WA
Posts: 22,302
Technical Contributor: For members who share their technical expertise. - Issue reason: Has been floating around the oze tech section for a long time and is always there to give advice when people have an issue. 
Default Re: Fault codes causing limp mode

If the inlet manifold is leaking it's usually at the bottom of number 1 or 6 inlet manifolds where they bolt onto the head. The best way to find it is too put a length (1/2 a metre) of windscreen sized tubing in one ear while moving the other end around under the manifold listening for a telltale sucking noise; do this with engine idling both when the engine is a hot and when it is cold as the change in head and manifold temperatures can sometimes temporarily close up any gap between the head and the manifold.
__________________
regards Blue
aussiblue is offline   Reply With Quote Multi-Quote with this Post
Old 08-07-2017, 07:07 PM   #12
aussiblue
FG XR6 Ute & Sedan
Donating Member3
 
Join Date: Oct 2006
Location: Bibra Lake WA
Posts: 22,302
Technical Contributor: For members who share their technical expertise. - Issue reason: Has been floating around the oze tech section for a long time and is always there to give advice when people have an issue. 
Default Re: Fault codes causing limp mode

The Electronic Control Unit (ECU) or Power Control Module (PCM) is in the engine bay on the passenger's side near the windscreen it's the aluminium box like this: http://www.ebay.com.au/itm/FORD-FALC...MAAOSwSlBYzI-N and this. As you can see the plugs are underneath on the engine side. Disconnect the battery and ensure the ignition is off and the key removed before playing with the plugs or unbolting the ECU/ PCM otherwise you risk damaging it.
__________________
regards Blue
aussiblue is offline   Reply With Quote Multi-Quote with this Post
Old 08-07-2017, 07:39 PM   #13
IH8HSV
XR6T 400kw(well one day!)
 
IH8HSV's Avatar
 
Join Date: Dec 2005
Location: Toodyay W.A.
Posts: 1,008
Default Re: Fault codes causing limp mode

Thanks Aussieblue.

I was reading that there is a Technical service bullitin for BF's stalling. TSB 20/05.

Something to do with cleaning the throttle body. Is there anyway I can read this?

Thanks.
__________________
If it Vibrates, rattles, squeaks or knocks - then it must be a Territory
IH8HSV is offline   Reply With Quote Multi-Quote with this Post
Old 08-07-2017, 07:41 PM   #14
IH8HSV
XR6T 400kw(well one day!)
 
IH8HSV's Avatar
 
Join Date: Dec 2005
Location: Toodyay W.A.
Posts: 1,008
Default Re: Fault codes causing limp mode

Also...

Can I clean the TPS?

If I do is there a procedure to ''re-learn' it when i put it back together?

Thanks
__________________
If it Vibrates, rattles, squeaks or knocks - then it must be a Territory
IH8HSV is offline   Reply With Quote Multi-Quote with this Post
Old 09-07-2017, 07:56 PM   #15
IH8HSV
XR6T 400kw(well one day!)
 
IH8HSV's Avatar
 
Join Date: Dec 2005
Location: Toodyay W.A.
Posts: 1,008
Default Re: Fault codes causing limp mode

Quote:
Originally Posted by lucas2 View Post
What's the battery like? That can cause issues and may be worth looking into before you go replacing lots of parts.
The battery is 3 years old. Sometimes I have to jump start it.

Are you saying that this can cause an intermittant problem?

Thanks.
__________________
If it Vibrates, rattles, squeaks or knocks - then it must be a Territory
IH8HSV is offline   Reply With Quote Multi-Quote with this Post
Old 09-07-2017, 08:11 PM   #16
aussiblue
FG XR6 Ute & Sedan
Donating Member3
 
Join Date: Oct 2006
Location: Bibra Lake WA
Posts: 22,302
Technical Contributor: For members who share their technical expertise. - Issue reason: Has been floating around the oze tech section for a long time and is always there to give advice when people have an issue. 
Default Re: Fault codes causing limp mode

Quote:
The battery is 3 years old. Sometimes I have to jump start it.

Are you saying that this can cause an intermittent problem?
They don't last any longer than that and if you have to sometimes jump start it, it's time for a new one. And yes a below par battery will cause both fault codes and running problems. The electronics, including the PCM, need a specified minimum voltage (can't find it at the moment but something like 9.6 volts I think).
__________________
regards Blue

Last edited by aussiblue; 09-07-2017 at 08:20 PM.
aussiblue is offline   Reply With Quote Multi-Quote with this Post
This user likes this post:
Old 09-07-2017, 08:30 PM   #17
IH8HSV
XR6T 400kw(well one day!)
 
IH8HSV's Avatar
 
Join Date: Dec 2005
Location: Toodyay W.A.
Posts: 1,008
Default Re: Fault codes causing limp mode

Quote:
Originally Posted by aussiblue View Post
They don't last any longer than that and if you have to sometimes jump start it, it's time for a new one. And yes a below par battery will cause both fault codes and running problems. The electronics, including the PCM, need a specified minimum voltage (can't find it at the moment but something like 9.6 volts I think).
Hmmm..

OK. That is interesting.

Maybe Ill start with that.

While im at it - where is the Idle control unit? I looked on top of throttle body but wasnt to sure which it was.

Was told to clean this too.

Thanks.
__________________
If it Vibrates, rattles, squeaks or knocks - then it must be a Territory

Last edited by IH8HSV; 09-07-2017 at 08:43 PM.
IH8HSV is offline   Reply With Quote Multi-Quote with this Post
Old 10-07-2017, 09:46 AM   #18
ratter
FF.Com.Au Hardcore
 
ratter's Avatar
 
Join Date: Feb 2005
Location: Pit Lane
Posts: 11,871
Valued Contributor: For members whose non technical contributions are worthy of recognition. - Issue reason: Shares his in-depth tuning knowledge with the forum, very helpful. Contributor: For members who make a contribution worthy of recognition. - Issue reason: For his indepth tutorial on adding borders to photographs 
Default Re: Fault codes causing limp mode

your throttle body is your idle control unit
__________________
Pit Lane Performance
20 Rosella St Frankston 03 9783 8122

Authorised Streetfighter, Pcmtec , SCT & HP Tuners Tuning Agent,
ratter is offline   Reply With Quote Multi-Quote with this Post
Old 10-07-2017, 05:13 PM   #19
IH8HSV
XR6T 400kw(well one day!)
 
IH8HSV's Avatar
 
Join Date: Dec 2005
Location: Toodyay W.A.
Posts: 1,008
Default Re: Fault codes causing limp mode

Ok,

Thanks for all that.

Im going to replace the battery, clean the throttle body and replace the TPS.

Hopefully that will cure it.

Thanks
__________________
If it Vibrates, rattles, squeaks or knocks - then it must be a Territory
IH8HSV is offline   Reply With Quote Multi-Quote with this Post
Old 29-09-2019, 11:57 AM   #20
rxrk
Starter Motor
 
Join Date: Sep 2019
Posts: 7
Default Re: Fault codes causing limp mode

According to the owners manual.
If your battery is 9 volts or below it will send the car into limp mode.
rxrk is offline   Reply With Quote Multi-Quote with this Post
Old 29-09-2019, 01:11 PM   #21
aussiblue
FG XR6 Ute & Sedan
Donating Member3
 
Join Date: Oct 2006
Location: Bibra Lake WA
Posts: 22,302
Technical Contributor: For members who share their technical expertise. - Issue reason: Has been floating around the oze tech section for a long time and is always there to give advice when people have an issue. 
Default Re: Fault codes causing limp mode

It might also be a failed throttle body as it is not uncommon. See https://fordforums.com.au/showthread.php?t=11479350
__________________
regards Blue
aussiblue is offline   Reply With Quote Multi-Quote with this Post
Old 28-02-2021, 12:04 PM   #22
3phase
Starter Motor
 
Join Date: Feb 2021
Posts: 2
Default Re: Fault codes causing limp mode

Did you ever get to the bottom of this? my car is doing exactly the same thing.
2003 BA falcon
3phase is offline   Reply With Quote Multi-Quote with this Post
Old 01-03-2023, 12:12 PM   #23
Fairlane420
Starter Motor
 
Join Date: Feb 2023
Posts: 5
Default Re: Fault codes causing limp mode

Hi mate did you fix this issue?
Fairlane420 is offline   Reply With Quote Multi-Quote with this Post
Old 02-03-2023, 10:09 AM   #24
3phase
Starter Motor
 
Join Date: Feb 2021
Posts: 2
Default Re: Fault codes causing limp mode

Yes, it was a faulty inlet gasket with my one.
Replaced it and she ran like a dream.
3phase is offline   Reply With Quote Multi-Quote with this Post
Reply

Thread Tools
Display Modes

Forum Jump


All times are GMT +11. The time now is 07:04 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Other than what is legally copyrighted by the respective owners, this site is copyright www.fordforums.com.au
Positive SSL