Welcome to the Australian Ford Forums forum.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact us.

Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated.

Go Back   Australian Ford Forums > Ford Australia Vehicles > Small and Mid Sized Cars > Focus

Reply
 
Thread Tools Display Modes
Old 22-07-2013, 07:17 PM   #1
TICK4D-TAS
Club Moderator
 
Join Date: Dec 2004
Location: Tas
Posts: 3,744
Default 06 Focus Zetec engine light

Howdy All,

My flat mates 06 Zetec has bought up the check engine light today. I put my SCT flash unit on it and it came up with the following codes

P116F
C276F
P0000

I then reset it with the SCT and started the car and it came up with these ones

P1100
P0100
P0000

I have found the P1100 and P0100 and they are related to the air flow meter, so was going to check that out and the wiring and air cleaner. Car was only serviced about 2 months ago and has done 116000ks. I haven't driven it since the reset to see if the light comes back on, but it didn't when I started the car after the reset.

Any info would be appreciated.

__________________
2001 T2 TS50
2002 T3 TS50
2006 FPV GT Racecar
2010 FPV F6 Ute
2016 FGX XR6 Sprint
2020 PX3 Ranger Wildtrak
TICK4D-TAS is offline   Reply With Quote Multi-Quote with this Post
Old 22-07-2013, 08:34 PM   #2
marg99
FF.Com.Au Hardcore
 
Join Date: Jul 2008
Location: Melbourne
Posts: 804
Default Re: 06 Focus Zetec engine light

A code P0100 may mean that one or more of the following has happened: The MAF may be disconnected, or a wiring connection may be bad The MAF sensor may be faulty
P1100 means Airflow meter signal is intermittent

Sounds most likely you need to clean all terminals and connectors relating to the airflow meter.
marg99 is offline   Reply With Quote Multi-Quote with this Post
Old 22-07-2013, 11:58 PM   #3
TICK4D-TAS
Club Moderator
 
Join Date: Dec 2004
Location: Tas
Posts: 3,744
Default Re: 06 Focus Zetec engine light

Thanks, I will give it a clean tomorrow afterwork and see how it goes.
__________________
2001 T2 TS50
2002 T3 TS50
2006 FPV GT Racecar
2010 FPV F6 Ute
2016 FGX XR6 Sprint
2020 PX3 Ranger Wildtrak
TICK4D-TAS is offline   Reply With Quote Multi-Quote with this Post
Old 01-01-2015, 04:59 PM   #4
phewyl
Starter Motor
 
Join Date: Sep 2013
Posts: 5
Default Re: 06 Focus Zetec engine light

What is the outcome? No good leaving a thread dead this way.
phewyl is offline   Reply With Quote Multi-Quote with this Post
Reply


Forum Jump


All times are GMT +11. The time now is 11:06 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Other than what is legally copyrighted by the respective owners, this site is copyright www.fordforums.com.au
Positive SSL