|
|
|
|
|
20-09-2011, 10:55 AM
|
#1 | ||
|
F6-557
Join Date: Feb 2005
Location: Adelaide.S.Aust.
Posts: 134
|
I have just realised half of the backlight for my LCD display in the instrument cluster on my AU2 XR8 is not working. Is this repairable and if so how do you go about it ? Thanks
|
||
|
|
|
20-09-2011, 11:21 AM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Aug 2006
Location: Salamander Bay
Posts: 5,427
|
there are 2 bulbs at the back they are mounted in green plastic from memory just twist and remove
__________________
[SIGPIC][/SIGPIC]
Everyone starts off with a bag full of luck and an empty bag of experience. The trick is to fill the experience bag before the luck bag is empty. "It is better to remain silent and be thought a fool than to speak out and remove all doubt." Start a new career as a bus driver Rides: FG2 XR6 stock at this stage but a very nice ride xc 4 DOOR X CHASER 5.8 UNDER RESTO |
||
|
|
|
|
20-09-2011, 11:24 AM
|
#3 | ||
|
I ♥ EDM
 
Join Date: Aug 2006
Posts: 5,092
|
It is repairable, its just one of light bulbs has blown.
Ok im not sure if theres a guide on here for it, so ill try to explain. On your instrument cluster there are 2 screwhole covers just on the top, remove them to expose the screws, take the screws out. This will allow you to slide the cluster out (all of this will be easier if you tilt your steering wheel down to its lowest point) There will be several wiring plugs that you can simply unplug, then behind the cluster youll notice all these "dial" looking things that are the housings for the bulbs. For the odometer display there are 2 bulbs, they will be physically directly behind where your odo display is, undo the one thats not working (from memory you should be able to do this by hand) There is an aftermarket NARVA part number for this, i cant remember it, but repco have them for only a few bucks. |
||
|
|
|
|
20-09-2011, 11:37 AM
|
#4 | ||
|
F6-557
Join Date: Feb 2005
Location: Adelaide.S.Aust.
Posts: 134
|
Ok thanks guys !!!
|
||
|
|
|
|
20-09-2011, 12:12 PM
|
#5 | ||
|
F6-557
Join Date: Feb 2005
Location: Adelaide.S.Aust.
Posts: 134
|
Any tricks to pulling in out ?
|
||
|
|
|
|
20-09-2011, 12:28 PM
|
#6 | |||
|
I ♥ EDM
Join Date: Aug 2006
Posts: 5,092
|
Quote:
There "may" be some clips holding it in i cant quite remember, just use the screwdriver to locate them to help pop it out. |
|||
|
|
|
|
20-09-2011, 12:44 PM
|
#7 | ||
|
FF.Com.Au Hardcore
Join Date: Aug 2007
Location: Brighton, Adelaide
Posts: 3,972
|
shoot down to u-pull-it there will be some AU's there and suss out the clips and screws that hold it all in/on.
im pretty sure there are some guides in the technical link up the top of the page, look for the AU link. here is one that may help you from there http://www.fordforums.com.au/vbporta...article&id=305 another thing to do to it while you have it out is a Led coloured light conversion there are heaps of different coloured ones available on ebay too. repco have a plug and play narva one available, for about $3ea autobarn sell them also i changed my EF and EL to spark blue, looks a lot better imo cheers, craig
__________________
Money Talks, but all i ever hear is it saying Goodbye!! |
||
|
|
|
|
23-09-2011, 04:02 PM
|
#8 | ||
|
F6-557
Join Date: Feb 2005
Location: Adelaide.S.Aust.
Posts: 134
|
Thanks for all the info guys . After about 6 attempts (having to calm myself down between each one) i finally got got the cluster out. I had to feed wire through the mounting bracket holes and also used a suction cup on the plastic face and pulled.Out it came.
I sourced the globes as mentioned from repco $2 each they are slightly different and are quite a tight fit but do the job. Thanks again. |
||
|
|
|
Instrument cluster LCD backlight
Re: Instrument cluster LCD backlight
Linear Mode
