|
|
|
|
|
12-05-2007, 10:06 AM
|
#1 | ||
|
Banned
Join Date: Aug 2006
Posts: 283
|
It is all put in and works well except for it doesnt change out of 3rd. It just stays in 3rd. Takes of in 3rd and does everything n 3rd. park, reverse and N work. any ideas? we got the cables caught in between the gearbox and engine when putting it up but didnt get to much pressure on it. easy way to say it is that i have gears
P R N 3 |
||
|
|
|
12-05-2007, 11:11 AM
|
#2 | |||
|
www.TUFFCARPARTS.com
Join Date: Feb 2006
Posts: 5,221
|
Quote:
__________________
http://i1233.photobucket.com/albums/...psc203b7b1.jpg |
|||
|
|
|
|
12-05-2007, 03:12 PM
|
#3 | ||
|
FF.Com.Au Hardcore
Join Date: May 2006
Location: Perth, South
Posts: 3,064
|
it would seem that more than likely the au ecu doesn't like the ba trans...haven't ba's got ion autos in them instead of btr's?
|
||
|
|
|
|
12-05-2007, 03:40 PM
|
#4 | ||
|
Banned
Join Date: Aug 2006
Posts: 283
|
nah its a btr transmission. if i damaged the cables going to the trans would that put it in limp mode?
|
||
|
|
|
|
12-05-2007, 03:54 PM
|
#5 | ||
|
AULTD
Join Date: Mar 2005
Location: Langwarrin
Posts: 818
|
Is your speedo working?
If not that also causes limp home mode |
||
|
|
|
|
12-05-2007, 04:41 PM
|
#6 | ||
|
Banned
Join Date: Aug 2006
Posts: 283
|
yeh we put a speedo drive on the shaft so its all working
|
||
|
|
|
|
12-05-2007, 09:25 PM
|
#7 | ||
|
AULTD
Join Date: Mar 2005
Location: Langwarrin
Posts: 818
|
The only other thing is maybe they changed the pinout on the transmission from AU to BA, but highly unlikely.
You could have been unlucky and damaged the wires. Check that the plugs are in firmly, especially the large round one. It sounds as if the the easy ones on the inhibitor switch are O.K. |
||
|
|
|
|
12-05-2007, 09:39 PM
|
#8 | ||
|
FF.Com.Au Hardcore
Join Date: May 2006
Location: Perth, South
Posts: 3,064
|
ba autos don't have a vss output on the trans, they get the reading from the abs sensors, that's why you don't have to get anything to adjust the speedo if you change to different wheels, it adjusts itself...apparently there's nowhere to put a speedo sensor in the trans itself
|
||
|
|
|
|
12-05-2007, 09:48 PM
|
#9 | ||
|
AULTD
Join Date: Mar 2005
Location: Langwarrin
Posts: 818
|
I just read on the E series section that bad earths can also cause limp home mode to kick in.
I think the auto was modified so that it would take the speed sensor from the AU. |
||
|
|
|
|
12-05-2007, 09:54 PM
|
#10 | ||
|
Banned
Join Date: Jan 2005
Location: Smoking the bags in a Turbo 6-speed ED!
Posts: 1,208
|
I'd like pics of the modded trans so show how the speed sensor is set up?
|
||
|
|
|
|
13-05-2007, 07:32 AM
|
#11 | ||||
|
Blown 5L coming
Join Date: Dec 2006
Location: Warwick, QLD
Posts: 1,997
|
Quote:
__________________
1995 EF Fairmont was stocko 6cyl with open single spin diff....NOW WITH XR8 ENGINE, DRIVELINE AND SUSPENSION!!!!! Maybe by the end of 2010 there may just be a blower as well ;) NEW CLUB FOR SUNSHINE COAST !! www.f-p-e.proboards.com Contact Col (au2sw) via PM or on MSN @ efmonty@hotmail.com Quote:
|
||||
|
|
|
|
13-05-2007, 06:07 PM
|
#12 | ||
|
AU2 XR8
Join Date: Dec 2005
Posts: 163
|
ba utes without abs have a speed sensor in them thats probally how he got away with it or he just put an older model extension housing on very easy i no there are some differences in grounding in the valve body on ba's compared to older models which will put it in limp mode try pulling the pan off and swapping your loom out of the au trans into the ba one it should plug straight just have to drop the valve body to get the ba loom out and put yours in reset the computer and see what happens hope that helps
cheers |
||
|
|
|
| This user likes this post: |
More Trouble With BA Trans In AU :(
Linear Mode
