Go Back   Australian Ford Forums > Club and Speciality Forums > Ford Car Clubs > FPV-Tickford Club of NSW > FPV-TCNSW Club Discussions

Reply
 
Thread Tools Display Modes
Old 20-08-2005, 06:10 PM   #1
greenman43
greenman43
 
greenman43's Avatar
 
Join Date: Jul 2005
Location: Sydney
Posts: 108
Default BA compliance plate location ?

Hi all, another question : can someone please tell me where I can locate the compliance plate on a BA, so I can check the factory options ? I can see two stickers on the RF strut tower, but logic tells me they must be using a permanent plate.

Thanks in advance (again!),
Brian

greenman43 is offline   Reply With Quote Multi-Quote with this Post
Old 21-08-2005, 08:02 AM   #2
geckoGT
Ich bin ein auslander
 
geckoGT's Avatar
 
Join Date: May 2005
Location: Loving the Endorphine Machine
Posts: 7,453
Valued Contributor: For members whose non technical contributions are worthy of recognition. - Issue reason: Always level headed and i notice him being the voice of reason when a thread may be getting heated 
Default

I have never seen one, as far as I know the sticker is it.
__________________
Growing old is compulsory, growing up is optional!
geckoGT is offline   Reply With Quote Multi-Quote with this Post
This user likes this post:
Old 21-08-2005, 09:41 AM   #3
Mondie
Firm member
 
Join Date: Jan 2005
Location: Adelaide Hills.
Posts: 458
Default

Yep, the sticker is it. Introduced with the BA as a security measure l believe.

On our Terri the sticker has moved to inside the drivers door frame due to them being suceptible to water damage under the bonnet. Not sure if the same change was made for the BA.
Mondie is offline   Reply With Quote Multi-Quote with this Post
Old 21-08-2005, 02:33 PM   #4
Smoke Pursuit
FF.Com.Au Hardcore
 
Join Date: Dec 2004
Posts: 22,928
Valued Contributor: For members whose non technical contributions are worthy of recognition. - Issue reason: DASH/bfiipursuit has been alot of help over the years I have frequented this forum, lots of thoughtful and informed posts, very much a valued contributor. 
Default

Yes the BAs also have it on the inside of the drivers door...

There is no such plate with "Factory Options" like the old Tickfords had, eg. 17 inch alloys, Sunroof, Body kit etc.
__________________
2022 RAM Laramie 5.7
2023.50 Ranger Wildtrak 3.0 V6 Premium Pack
2024 Everest Sport 3.0 V6 Touring Pack
2025 Mustang Darkhorse 6M Blue Ember + Appearance pack ETA April 25.
Smoke Pursuit is offline   Reply With Quote Multi-Quote with this Post
Old 21-08-2005, 09:54 PM   #5
greenman43
greenman43
 
greenman43's Avatar
 
Join Date: Jul 2005
Location: Sydney
Posts: 108
Default Thanks to all

Thanks guys, the Ford dealer today confirmed your comments, very much appreciated.

Cheers,
Brian
greenman43 is offline   Reply With Quote Multi-Quote with this Post
Old 08-11-2005, 12:47 AM   #6
XD-Machine
proud xd owner
 
XD-Machine's Avatar
 
Join Date: Jul 2005
Location: penriff (penrith), sydney
Posts: 973
Default

thats just cheap no compliance plate. whouldnt it be easier to change with the right equitment, plus will they last forever like the old metal ones
__________________
Falcon-Tickford-FPV
car club of nsw

My XD's progress http://www.fordforums.com.au/showthread.php?t=20847
XD-Machine is offline   Reply With Quote Multi-Quote with this Post
Old 23-07-2019, 02:13 PM   #7
Bilford
Starter Motor
 
Join Date: Oct 2016
Posts: 10
Default Re: BA compliance plate location ?

NO com plate as such, just vin stickers, or when standing at front of car on the RHS follow the top inside edge of the guard up and when you get about 7cm from the bonnet strut there is a factory check out in the guard if you look close in that gap which is about 1cm x 9cm there is a VIN stamped into the car. In relation to XR8 Boss 5.4 the engine number's, the number is on the block behind the alternator if it its boss or GT the block number starts with FPV...…. not the last half of the vin like a fellow wrote down on the roadworthy for the guy I brought if off. If your rig is a boss or GT the Engine no: DOES NOT start JGS.... They start with FPV, the alternator has got to come off to see it . I asked my mechanic to do a service take the alternator off, take a pic, and give me a new roadworthy with the correct Engine no:, took it to transport there was NO drama's. grab the form 'alter Registration details'.
Bilford is offline   Reply With Quote Multi-Quote with this Post
Reply


Forum Jump


All times are GMT +11. The time now is 02:12 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Other than what is legally copyrighted by the respective owners, this site is copyright www.fordforums.com.au
Positive SSL